Fix: Teredo Tunneling Pseudo-Interface in Windows OS?

Teredo is an automatic mechanism for tunneling. It is based on 6in4 for obtaining better access to the IPv6 internet from a single node in an IPv4- only network. It also has Nat Traversal giving it the advantage of working even behind a NAT44 gateway. It’s vital to understand what is Teredo Tunneling Pseudo-Interface used for.  It is a process of tunneling IPv6 traffic over an IPv4 network. Teredo is a transition technology.

microsoft teredo tunneling adapter

IP stands for Internet Protocol, which is a communication protocol performing the task of identifying and locating the computers on networks and routing of traffic across the Internet. IPv4 addresses are 32-bit address allowing a maximum of over 4 billions different address. When there is the rapid growth of the Internet, it refers that there will not be enough free IPv4 addresses to allow new devices to connect.

In order to solve this problem of connectivity, a new protocol called IPv6 is developed. IPv6 address uses 128-bit address with a format of four hexadecimal digits that are separated by colons like fe80:: 12ac:fe44:192a:14cc). This allows many devices to get connected. During this period of transition from IPv4 to IPv6, a temporary method is used which called Teredo is tunneling.

What is Microsoft Teredo Tunneling Adapter?

Microsoft Teredo Tunneling Adapter is being used for repackaging the data packets and this also permits communication between IPv4 and IPv6 devices. The communication is made possible by the use of a 6to4 protocol for tunneling IPv6 data to a device with an IPv4 address. There is also Teredo tunneling pseudo adaptor driver in windows which is available on the net.

TheTeredo Tunneling Adapter server runs a publicly accessible IPv4 address. It forwards the IPv4 encapsulated IPv6 packet to the required destination. Teredo server allows its user to use “keep alive” traffic with the use of the server. This also keeps the NAT mapping between the client’s source port and the public IP address. This also allows a “refresh” interval that enables the user to verify if the source port is valid. The interval varies with the Teredo service. Source ports may change but Teredo server must have the knowledge to return back to its clients. Teredo keeps track for both the public IP address as well as the source port of the user.

When teredo tunneling occurs you may receive an error message indicating that “Teredo Tunneling Pseudo-Interface Code 10This device cannot start Code 10”. On certain systems, you may also receive a bang next to Teredo Tunneling Device in the device manager. While you are trying to update this device for installation of the driver, your driver installation may not take place by leaving an error message. To fix this issue you need to perform the following steps:

Fix Using Command prompt

  • With administrator credentials, you have to open a command prompt. To complete this action you need to find CMD and then have to right click on Run as Administrator.
  • Now you have to type netsh and need to press Enter.
  • Write “int teredo” and again press Enter.
  • Type “set state disabled” here before pressing Enter.
  • Then you need to open Device Manager and have to uninstall Teredo Tunneling Pseudo-Interface.
  • After typing you need to go back to the command prompt and have to type netsh again and have to hit Enter.
  • After completing these steps, you need to type ipv6 and have to hit Enter.
  • Now return to the Device Manager and keep Scanning for New Hardware.
  • After completing the scan, click Show Hidden Devices from the view menu.

If the above-mentioned steps are completed carefully then the Teredo Tunneling Pseudo-Interface Windows 10 will be present without any errors. In case of failure to solve the problem by following the above-mentioned steps, then further steps can be taken for editing the registry for the purpose of solving the error message.

teredo tunneling adapter, teredo tunneling pseudo-interface, tunnel adapter teredo tunneling pseudo-interface

Note: It is highly advisable to backup your registry before attempting to change anything. Editing the registry can change the files that are required for the operating system to load. Thus, to have a backup will enable you to restore the original data.

Fix Teredo from the Registry

  • First, click on the Start button.
  • As the Start menu appears type “regedit” for opening the registry editor.
  • Then you need to navigate to “HKEY_LOCAL_MACHINE\SYSTEM\CURRENTCONTROLSET\SERVICES\TCPIP6\PARAMETERS” on the left side.
  • Here you need to select Parameters.
  • You will be provided with the option of Disabled Components.
  • Select and click on the option – Disabled Components.
  • After selection, set the DWORD value to 0.
  • Now you need to close the Registry Editor and have to Reboot your system.
  • After rebooting, the error message issue will be solved for Teredo Tunneling Pseudo-Interface.

Fix Teredo in Windows 10 Only

Many users face the problem of Teredo Tunneling Pseudo. The problem may arise if you are having an incomplete driver or it may also indicate that your system is missing a proper device driver. In order to fix this particular problem you need to follow the steps mentioned below:

– You need to uninstall the already existing device manager driver before you install a new one.

  • For uninstalling the existing driver with a new one you need to open Device Manager by selecting the start option.
  • From the start menu choose Control Panel.
  • Then select System and maintenance followed by clicking Device Manager.

Note: If you receive a message asking for an administrator password or confirmation, then you need to type the password or the confirmation as required.

  • Then you need to right click on the sound card by locating it properly.
  • Here you need to select properties.
  • In the final step, you need to go to the driver tab and need to select the Uninstall button for uninstalling the driver that is associated with your device.

– As soon as the uninstalling procedure ends you need to restart your system for allowing it to work properly.

Note: In certain cases, only updating the old driver with the new one fails to bring a proper solution to the issue. In such a case you need to follow the steps below.

Fix: SVCHOST.EXE and MSMPENG.EXE

Antivirus software’s are the leading force to fight against computer viruses and any other security threats. You should not disable any anti-virus software except a few. In such cases where you are in dire need to uninstall the security virus, you must again reinstall it as soon as you are complete with your work. While you having access to the internet connection without any active antivirus software, your system is highly prone to attacks. It’s also important to disable Teredo tunneling pseudo-interface.

– Then you need to try to install the drivers.

  • Here you need to click on the Start button.
  • As the Start menu appears, you need to click on Control panel and further need to click on System and Maintenance.
  • From the System and Maintenance menu, you need to select the Device Manager option.
  • If asking for any confirmation or any password, you need to provide the same.
  • You need to locate the sound card.
  • Select the sound card and select the properties.
  • Then you need to go to the driver tab and have to select the Uninstall option to uninstall the driver that is associated with the device.
  • In the final step, you need to restart your computer and then have to install the latest driver.

Fix Teredo in Windows 10 and Windows 8/8.1

While your system is facing tunnel adapter teredo tunneling pseudo-interface problem, you can fix the problem by re-installing the same. While installation you need to follow the steps mentioned below:

Method 1

  • Make all your antivirus software and Firewall disable temporarily.
  • Go to the Start button.
  • As the Search menu appears, you need to type services.msc in the Start search box that appears.
  • After typing, press Enter.
  • Then right click is required in the Peer Networking Grouping service.
  • Now you need to select Properties.
  • Check for the services, if started or not.
  • If services are not yet working, you need to Right-click on it.
  • Select and click the Start option.
  • You can also try to set the Start-up type making it Automatic under properties.
  • In the end, click on the OK button to complete the entire process.

Method 2

In order to get the teredo tunneling pseudo-interface windows 10 fix you can also follow the steps that are mentioned below:

Note: In the first step you need to disable and re-enable IPv6.

  • Disabling IPv6

To disable IPv6 you need to uninstall IPv6. For removing IPv6 –

  • Select the Start button.
  • As the Start menu appears, you have to type Network and Sharing Centre.
  • Then you need to select Local Area Network.
  • After the selection of the network, you need to go into the properties of every single network adapter.
  • Then you need to either uncheck the box which is next to the protocol “Internet Protocol version 6(TCP/IPv6), as this will disable it, or you need to select it and have to click uninstall, as this will remove it off the computer.
  • Now you need to Restart your computer.

Re-enable the IPv6:

To re-enable the IPv6 you need to complete the following steps :

teredo tunneling adapter, teredo tunneling pseudo-interface, tunnel adapter teredo tunneling pseudo-interface

  • You need to click on the Start button.
  • On the Start menu, type Network and Sharing Centre on the Start search box.
  • Then you need to select Local Area Network.
  • After network selection, you need to check the properties for every network adaptor.
  • Then you need to put a check mark or need to select Install. This will make the installation of IPv6.
  • As the installation is complete, you need to Restart the system.

Even after following all these steps discussed above, your problem is not fixed and you continue to get  Error Code 10 you can now follow the steps below:

  • At first, need to go the Start option.
  • On the appearance of the Start menu, type cmd in the Start search box.
  • Then right click on the cmd at the top of the list and then need to select Run as Administrator.
  • As the User Account Control window appears you have to click on Yes.

Note: You need to be very careful while typing all these commands. After typing each of the commands, you need to hit the Enter key on the keyboard. Any mistyping of command may also lead to malfunction of your device.

Fix Teredo in Windows 7 and Windows XP

For users with Windows 7 Operating System, the Teredo tunneling pseudo-interface windows 7 & XP problem can be disabled by following the steps below:

  1. Log in with your admin account in windows 7
  2. Now right click on Computer and choose the option “Manage”.
  3. In the menu that is located on the left side under System Tools, you need to left-click on “Device manager”.
  4. Right-click on “Device Manager”.
  5. Move over “View” > and here click on “Show Hidden Devices” in the popup menu.
  6. You need to look for a group called “Network Adapters”.
  7. Expand it by double-clicking in it.
  8. Find a list of all adapters, including the one that is disabled.

Note: If Teredo driver is uninstalled, it is not easy to reinstall it just by scanning for new hardware. It is not a Plug and Play device. To reinstall the Teredo driver you need to install it manually as a legacy driver. You can find this from “Add driver > Manual installation > Network interface > Select driver > Microsoft > Microsoft Teredo Tunneling Pseudo-interface.

Conclusion :

After following the above steps properly the problem of Teredo tunneling pseudo-interface windows 7 will be solved. You must be absolutely careful while performing the entire procedure. Mistype of any single command or a wrong click may result in absolute failure.

Leave a Reply

Your email address will not be published. Required fields are marked *